電動伸縮門檢測

電動伸縮門檢測項目報價？??解決方案？??檢測周期？??樣品要求？

點 擊 解 答??

GB/T 6104.1-2018工業車輛 術語和分類 第1部分:工業車輛類型

GB/T 6104的本部分規定了工業車輛的術語和分類。本部分中“工業車輛”是指至少有三個車輪，并帶有動力或非動力驅動裝置的輪式車輛(軌道上運行的車輛除外)，設計用于搬運、牽引、推頂、起升、堆垛或在貨架上分層堆垛各種貨物，并由一個操作者控制或無人駕駛自動控制。

GB/T 6104-2005機動工業車輛 術語

本標準規定了機動工業車輛分類的術語和定義、也規定了主要部件及其所屬附件的術語和定義。 某些術語并未給出定義、是因為它們是不言而喻的，或是因為它們通常在別的地方也使用。 在適當地方，采用插圖闡明定義。 本標準的附錄中給出了與工業拖車及其作業區域有關的術語和定義。

GB/T 10827.1-2014工業車輛 安全要求和驗證 第1部分:自行式工業車輛(除無人駕駛車輛、伸縮臂式叉車和載運車)

GB 10827的本部分規定了如ISO 5053所定義的下列自行式工業車輛(以下簡稱“車輛”)的安全要求及其驗證方法:a) 平衡重式叉車;b) 前移式叉車(具有可伸縮的門架或貨叉架);c) 插腿式叉車;d) 托盤堆垛車;e) 高起升平臺搬運車;f) 操作臺起升高度不大于1 200 mm的車輛;g) 側面式叉車(單側);h) 側面堆垛式叉車(兩側和三向);i) 托盤搬運車;j) 雙向和多向運行叉車;k) 牽引力不大于20 000N的牽引車;l) 平衡重式越野叉車;m) 其他以蓄電池、柴油、汽油或液化石油氣為動力的工業車輛。對于操作臺起升高度大于1 200 mm的車輛和/或帶著載荷起升至1 200 mm以上運行的車輛,本部分應與ISO 3691-3一起使用。本部分不適用于自行式伸縮臂式叉車、無人駕駛車輛和載運車,ISO 3691-2、ISO 3691-4和ISO 3691-6分別適用于這些車輛。本部分不適用于在苛刻條件下(如極端天氣、冷庫應用、危險環境)工作的車輛,這些情況需要有特殊防護措施。本部分涉及了除以下情形外,有關機械在制造商預期用途下使用和可預見條件下誤用的,如附錄B所列的所有重大危險、危險狀態或危險事件。本部分不包括下列情況可能發生的危險:--在制造過程中;--搬運能自由擺動的懸吊載荷時;--在公路上使用時;--在潛在爆炸性環境中操作時;--在與貨架之間的單側間隙小于500 mm的狹窄通道上使用時;--駕駛拖曳載荷的坐駕式車輛時,由于采用非人類工效學姿勢而引起;--駕駛額定起重量大于10 000 kg

TSG N0001-2017場(廠)內專用機動車輛安全技術監察規程

為了保障場(廠)內專用機動車輛安全使用，預防和減少事故，保護人民生命和財產安全，促進經濟社會發展，根據《中華人民共和國特種設備安全法》《特種設備安全監察條例》，制定本規程。根據《特種設備目錄》，場(廠)內專用機動車輛(以下簡稱場車)，是指除道路交通、農用車輛以外僅在工廠廠區、旅游景區、游樂場所等特定區域使用的專用機動車輛，包括機動工業車輛和非公路用旅游觀光車輛。

GA/T 548-2012公安裝備資產分類與代碼

本標準規定了公安裝備資產的分類、代碼及計量單位。本標準適用于公安裝備資產管理、清查、登記、統計及相關信息化應用系統建設等工作。

GYD 901-2002關于發布《統一建筑裝飾裝修工程消耗量定額》的通知

本定額適用于新建、擴建和改建工程的建筑裝飾裝修。

JG/T 154-2013電動伸縮圍墻大門

本標準規定了電動伸縮圍墻大門(簡稱電動伸縮門)的分類和標記、要求、試驗方法、檢驗規則、標志、包裝、運輸、貯存等內容。本標準適用于工業與民用建筑用的電動伸縮門。

JG/T 462-2014平開門和推拉門電動開門機

本標準規定了平開門和推拉門電動開門機的產品分類、要求、試驗方法、檢驗規則、標志、包裝、運輸及貯存。本標準適用于工業與民用建筑平開門及折疊門、推拉門及伸縮門使用的電動開門機。

DL/T 5056-2007變電站總布置設計技術規程

本標準規定了變電站總布置設計的基本技術要求。本標準適用于電壓等級為110kV~750kV新建或擴建變電站的總布置設計。對750kV以上電壓等級的變電站、改建的變電站以及換流站的總布置設計可參照使用。

DL/T 5218-2012220kV~750kV變電站設計技術規程

本標準適用于交流電壓為220kV～750kV變電站(開關站)新建及改、擴建工程的設計。

DL/T 5495-201535kV~110kV戶內變電站設計規程

本標準適用于交流電壓為35kV～110kV戶內變電站新建及改、擴建工程的設計。

DL/T 5496-2015220kV~500kV戶內變電站設計規程

本標準適用于交流電壓為220kV～500kV戶內變電站(開關站)新建及改、擴建工程的設計。

DL/T 5498-2015330kV~500kV無人值班變電站設計技術規程

本標準適用于330kV～500kV無人值班變電站或開關站新建及改、擴建工程的設計。

EN 81-3-2000電梯建造和安裝的安全規則.第3部分:電和液壓維修電梯;包含修改件A1-2008;合并勘誤表2009年7月

This standard specifies the safety rules for the construction and installation of permanently installed new electric service lifts with traction or positive drive; or hydraulic service lifts defined as lifting equipment; serving defined landing levels; having a car; the interior of which is regarded as inaccessible to persons on account of its dimensions and means of construction; suspended by ropes or chains or supported by a ram and moving between rigid vertical guide rails or guide rails whose inclination to the vertical does not exceed 15° and driven electrically or hydraulically.This standard covers service lifts with rated load not exceeding 300 kilogrammes and not intended to move persons. In addition to the requirements of this standard supplementary requirements shall be considered in special cases (potentially explosive atmosphere; extreme climate conditions; seismic conditions; transporting dangerous goods; etc.).This standard does not cover: a) service lifts with drives other than stated in; b) important modifications (see annex E) to a service lift installed beforeThis standard is brought into application; c) lifting appliances; such as paternosters; mines lifts; theatrical lifts; appliances with automatic caging; skips and hoists for building and public works sites; ships' hoists; platforms for exploration or drilling at sea; construction and maintenance appliances; d) installations where the inclination of the guide rails to the vertical exceeds 15°; e) safety during transport; installation; repairs and dismantling of service lifts; f) the use of glass for the walls of the well; for the car and for the landing doors including the vision panels. However;This standard may usefully be taken as a basis. Noise and vibrations are not dealt with inThis standard because these are not relevant to the safe use of the service lift. Fire propagation is not dealt with inThis standard. To satisfy the condition of inaccessibility to the car; the car dimensions shall not exceed: a) for floor area; 1;0 m2; b) for depth; 1;0 m; c) for height; 1;20 m. The height of 1;20 m shall not be limited if the car comprises several permanent compartments; each of which satisfies the above requirements. In particular; lifting equipment intended exclusively for the transportation of goods; but having a car with dimensions exceeding any one of the figures above shall not be entered in the category 'service lifts'.This standard covers the safety requirements for service lifts with rated speeds up to 1 m/s. NOTE For service lifts with higher rated speeds additional requirements shall be applied as appropriate in order to maintain the same level of safety.

EN 81-31-2010電梯制造與安裝安全規范.僅貨運電梯.第31部分:僅運送貨物的電梯

This European Standard applies to new electric accessible goods only lifts with traction or positive drive and new hydraulic accessible goods only lifts; permanently installed in restricted areas and/or only used by authorised and instructed persons (users); serving fixed and permanent landing levels; having a load carrying unit made of a single load carrying area; designed for the transportation of goods only; moving along a fixed path (e. g. scissor lifts; lifts with guide rails) and inclined not more than 15° to the vertical; with rated speed not exceeding 1 m/s.This European Standard covers accessible goods only lifts with rated load exceeding 300 kg and not intended to move persons.This standard deals with all significant hazards; hazardous situations and events with the exception of those listed in below; relevant to accessible goods only lifts; when they are used as intended and under the conditions foreseen by the manufacturer.

NF P82-410-2008電梯建造和安裝的安全規則.第3部分:電動和液壓電梯

La présente norme précise les règles de sécurité pour la construction et l'installation à demeure de monte-charge neufs électriques à entra?nement par adhérence ou à treuil attelé, ou de monte-charge neufs hydrauliques, définis comme équipement de levage, desservant des niveaux définis, comportant une cabine dont l'intérieur est inaccessible aux personnes en raison de ses dimensions et de sa constitution, suspendue par des cables ou cha?nes ou supportée par un vérin et se dépla?ant au moins partiellement le long de guides rigides verticaux ou dont l'angle avec la verticale n'excède pas 15o.La présente norme concerne les monte-charge de charge nominale n'excédant pas 300 kg et non prévus pour déplacer des personnes.Outre les prescriptions de la présente norme, des prescriptions supplémentaires doivent être prises en compte dans des cas particuliers (atmosphère explosible, conditions climatiques extrêmes, conditions sismiques, transport de produits dangereux, etc.).

DIN EN 81-3-2011電梯建造和安裝的安全規則.第3部分:電動和液壓載貨升降機;德文版本EN 81-3-2000+A1-2008 + AC-2009

1.1 This standard specifies the safety rules for the construction and installation of permanently installed new electric service lifts with traction or positive drive, or hydraulic service lifts defined as lifting equipment, serving defined landing levels, having a car, the interior of which is regarded as inaccessible to persons on account of its dimensions and means of construction, suspended by ropes or chains or supported by a ram and moving between rigid vertical guide rails or guide rails whose inclination to the vertical does not exceed 15° and driven electrically or hydraulically.This standard covers service lifts with rated load not exceeding 300 kilogrammes and not intended to move persons.1.2 In addition to the requirements of this standard supplementary requirements shall be considered in special cases (potentially explosive atmosphere, extreme climate conditions, seismic conditions, transporting dangerous goods, etc.).1.3 This standard does not cover:a) service lifts with drives other than statedb) important modifications (see annex E) to a service lift installed before this standard is brought into application;c) lifting appliances, such as paternosters, mines lifts, theatrical lifts, appliances with automatic caging, skips and hoists for building and public works sites, ships' hoists, platforms for exploration or drilling at sea, construction and maintenance appliances;d) installations where the inclination of the guide rails to the vertical exceeds 15°;e) safety during transport, installation, repairs and dismantling of service lifts;f) the use of glass for the walls of the well, for the car and for the landing doors including the vision panels.However, this standard may usefully be taken as a basis.Noise and vibrations are not dealt with in this standard because these are not relevant to the safe use of the service lift.Fire propagation is not dealt with in this standard.1.4 To satisfy the condition of inaccessibility to the car, the car dimensions shall not exceed:a) for floor area, 1,0 m2;b) for depth, 1,0 m;c) for height, 1,20 m.The height of 1,20 m shall not be limited if the car comprises several permanent compartments, each of which satisfies the above requirements.In particular, lifting equipment intended exclusively for the transportation of goods, but having a car with dimensions exceeding any one of the figures above shall not be entered in the category 'service lifts'.1.5 This standard covers the safety requirements for service lifts with rated speeds up to 1 m/s. NOTE For service lifts with higher rated speeds additional requirements shall be applied as appropriate in order to maintain the same level of safety.

DIN EN ISO 2867-2011土方機械.通道裝置(ISO 2867-2011);德文版本EN ISO 2867-2011

This International Standard specifies criteria for systems that provide access to the operator station and to routhe maintenance points on earth-moving machinery as defined in ISO 6165.